간행물
한국기계기술학회지 KCI 등재 Journal of the Korean Society of Mechanical Technology 韓國機械技術學會誌
- 발행기관 한국기계기술학회
- 자료유형 학술지
- 간기 격월간
- ISSN 1229-604X (Print)2092-0385 (Online)
- 수록기간 1999 ~ 2024
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
제21권 제6호 (2019년 12월) 32건
<학술연구>
21.
2019.12
구독 인증기관 무료, 개인회원 유료
In this study, the uniformity of the horizontal velocity and the temperature of each zone were investigated by computerized analysis method to divide the drying room into three multi - rooms to ensure the uniformity of flow inside the forced convection hot air dryer. The internal structure of the drying room of the dryer was modeled using Solidworks. In order to control the flow of hot air circulating in the drying chamber, the possibility of controlling the horizontal flow inside the drying room was verified by using a perforated plate, a guide vane, and a vertical plate. From the results of the flow visualization in the drying room, it was understood that the internal flows of the dryer models 1, 2 and 3 change from ununiform flow to uniform flow. From the analysis of velocity and temperature fluctuation, the results of the analysis of the dryer model 3 satisfied the design conditions.
4,000원
22.
2019.12
구독 인증기관 무료, 개인회원 유료
This paper proposes a method to reduce the pose error and to solve the dead reckoning issue which occurs when the mobile robot with continuous-tracks travels in the unstructured environments. When the continuous-track type mobile platform travels on terrain such as sand, gravel, stairs and etc., slippage occurs and thus the driving state of the mobile robot cannot be recognized normally. To compensate for this pose error, the proposed method utilizes optical flow estimation detected by camera. This method is tested through experiment. Finally, This method reduces the pose error detected on inertia measurement unit within some limit, while the pose error of without compensation increases without limit during robot move.
4,000원
23.
2019.12
구독 인증기관 무료, 개인회원 유료
In this study, the energy use of buildings was compared and analyzed by using weather data predicted with machine running techniques. Python was used as a predictive program to predict weather data and TRNSYS was used to simulate the energy usage of buildings. For weather forecasting, weather data from 1 August to 7 August were studied to forecast ambient air temperature and solar radiation. The lowest error came in seven days, with the outside air temperature standing at 1.8 percent and the solar radiation at 2.4 percent. The energy use of the building was simulated by using weather data predicted through the 7 days learning data with the lowest error. As a result , the error rate of cooling energy use was 1.92%, the sum of cooling energy and lighting energy use was 1.79%, and the building control by using predicted weather data didn’t show a big difference with just control.
4,000원
24.
2019.12
구독 인증기관 무료, 개인회원 유료
Due to rapid industrialization and urbanization, maintenance of high voltage transmission lines in narrow alleys, complex roads, or old factory areas is required. Since the existing aerial lift vehicle is made of steel, there is a risk of electric shock. Therefore, there is a need for the development of an insulated aerial lift vehicle that can prevent electric shock accidents during electrical work. In particular, the development of an insulated aerial lift vehicle is required in a recent work environment where live line work is inevitable. The development of composite insulation boom for the vertical swing type aerial lift vehicle is studied. The insulated boom was developed by applying glass fiber-epoxy composite and filament winding process. The developed insulated boom was verified by measuring dielectric breakdown strength, surface resistance and volume resistance according to ASTM D149 and ASTM D257.
3,000원
<생산기술>
25.
2019.12
구독 인증기관 무료, 개인회원 유료
Cassettes are a key component for power transmission and smooth shifting, and their construction consists of sprockets and spiders. The sprocket receives the force generated by pressing the pedal through the chain and rotates the rear wheel. It is a circular part. As the shifting system for efficient driving of bicycles has been developed, chains and sprockets require more complicated shapes than the conventional ones, and researches are being conducted to increase the production efficiency of sprockets. Cr-Mo steel is mainly used as the material for sprockets, but the trend of converting high-performance cassette material to titanium, which is a material with high specific strength, is gradually increasing. In this study, we also studied the molding technology of titanium material for the 5th and 6th stage shape design, the finite element analysis and the mass production using the press mold.
4,000원
26.
2019.12
구독 인증기관 무료, 개인회원 유료
As carbon fibers have the high performance, such as high strength, light weight, and high corrosion resistance, they are gradually expanding and growing at various industries. In particular, this study was conducted to determine whether the market could be applied to street lanterns among the construction sectors expected to grow in scale. In this study, the material characteristics of street lanterns using carbon fiber composites were studied in order to determine whether carbon fiber composites could be applied as a substitute for stainless steel and cast iron street lanterns. The physical relationship was experimentally evaluated to obtain a suitable material through the comparison of physical properties of fiber composite materials.
4,000원
27.
2019.12
구독 인증기관 무료, 개인회원 유료
The technology competitions of automobile manufacturers are getting hot. The characteristics of the environment friendly automobile are not only lowering the emission of harmful exhaust gas through the change of the power source, but also paying great attention to improvement of the power efficiency. As the market for pure electric vehicles continues to grow, we have analyzed the global technology competitiveness by DCT (Dual Clutch Transmission) patents. Clustering can be classified into five types ; 1) a cluster associated with a dual clutch transmission system, 2) a cluster of a torque transmission device and a reverse speed ratio, 3) a cluster of co-planar sets and dual clutch assemblies related to transmitting devices, 4) Device clusters, and 5) a cluster of synchronizers and clusters to prevent simultaneous operation of dual clutch transmissions. In recent years, demand for pure electric vehicles has been rapidly increasing, and patent applications related to DCT have been steadily increasing for energy efficiency of motor power sources.
4,000원
28.
2019.12
구독 인증기관 무료, 개인회원 유료
In this study, the injection pressure of 31 MPa and clamping force of 1,000 kN toggle electric injection molding machine were used to measure the load transmitted to the frame during injection molding and to use it as the design basis data. In general, the toggle structure is composed of a movable plate, tie bars, crossheads, toggle links, toggle pins, base plates, etc and The material is spherical graphite cast iron(FCD 400). In this study, it was found that there was a 1.3% safety factor by calculating the clamping force in the structure of the five-point toggle link system. In addition, Expected static bottom load, Expected dynamic additional load, Maximum expected additional load, and Maximum weight load were measured using tensile measurements and presented as important basic design data of the assembly.
4,000원
29.
2019.12
구독 인증기관 무료, 개인회원 유료
Deicing agent refers to the substance that melts snow by exothermic or endothermic chemical reaction after spraying on snow. It also has the function of reducing the freezing point to prevent freezing. However, the long-term use of deicing agent can cause some negative problems, such as pot hole, concrete corrosion, vehicle and steel bridge parts corrosion. At present, wet salt spray deicing is a cost-effective deicing method that is being widely used. Typical deicing agents are calcium chloride and sodium chloride. Deicing equipment is placed to similar or higher corrosive environment than coastal or marine environment due to direct contact to chloride in deicing operation. Therefore, the anti-corrosion control is very important for the maintenance of deicing equipment. In this study, corrosion resistance, blistering and repairability of the deicing equipment were tested by using test standard (salt water production and spraying- KS D 9502 , evaluating degree of rusting- ASTM D 610, evaluating degree of blistering- ASTM D 714, pull-off strangth of coatings- ASTM D 4541). And an economical coating system with long-term antirust performance was constructed. The results show that the performance of the coating system has been improved than with the original coating.
4,000원
30.
2019.12
구독 인증기관 무료, 개인회원 유료
FDM 3D Printer is used in maker space for mass production by the maker. Makers desire to manufacture products in a variety of colors using ABS Filaments. The purpose of this study is to identify the relation between the color of resin and each position on the bed. So, when printed using the 3D Printer, we found out the difference in the colors that it appears depending on the position of the bed. To see the difference in color, basic, blue, yellow, white, and black were selected and the bed plate was divided into three sections. Specimens were measured to obtain delta E values between each sections by the chromatic differential system. Obtained delta values were analyzed by the NBS system. As a result, the delta E value of black was found to correspond to “Appreciable”. In most cases, delta E values between the middle and the outer or the inner and the outer was greater than values between the middle and the inner. Using Infrared Thermal Camera, We found that the color difference relates 3D printing positions and temperatures. As a result, the 3D printing bed positions should be considered when 3D printing mass production.
4,000원
31.
2019.12
구독 인증기관 무료, 개인회원 유료
In this study, simulation studies were conducted to develop insert injection molds to improve the mass production of terminal assemblies. For the main part of the automobile door latch, charging, holding pressure and deformation analysis were performed according to the gate position of the injection process. As a result of injection molding analysis of the terminal assembly, the flow pattern was uniformly made while maintaining a constant balance of the filling of the product, and the pressure distribution at the time of filling was confirmed. When the analysis results are applied to the mold fabrication in the improved structural method, the transfer lines of the molten resin are controlled by the dam of the 1st injection molding, so that the transmission line is not short-circuited or deformed, and the watertightness, corrosion resistance, and good surface We believe the injection will be possible.
4,000원
32.
2019.12
구독 인증기관 무료, 개인회원 유료
The Carbon Fiber Reinforced Plastic(CFRP) is used in many industrial areas owing to its excellent specific strength. In order to be utilized for machine parts, it is needed to have the hole drilling machining that presents the excellent surface. For the excellent hole machining of CFRP, this study evaluated the cutting force and remaining burr in accordance with changes in temperature by cooling down the temperature of the machining part. It could be used for other machining of composite materials produced by laminating fabric.
4,000원
1
2
