본 연구의 목적은 문헌고찰을 근거로 보호관찰정보시스템 입력 정보 중 전자발찌 부착 성폭력범죄자의 재범 유발 변인을 선정하고 해당 변인과 재범 여부의 관련성을 실증적으로 확인하는 것이다. 이와 같은 목적을 달성하기 위해서 본 연구는 보호관찰 정보시스템에서 총 440명의 전자발찌 부착 성폭력범죄자를 무작위로 추출해서 DB를 구축하였다(비재범자: 220명, 재범자: 220명). 구축된 DB를 대상으로 이항 로지스틱 회귀분석을 실시한 결과, 전자발찌 부착 성폭력범죄 이전의 범죄 경력 중 이전 총 범 죄횟수와 이전 성폭력범죄횟수는 재범과 유의미한 정적인 관련성이 있었다. 또한 처벌 강도 중 전자발찌 부착기간은 재범과 유의미하게 정적으로 관련된 것으로 나타났다. 반면 사회적 결속과 관련해서 전자발찌 부착 성폭력범죄자가 직업이 있거나 배우자가 있는 경우가 직업이 없거나 배우자가 없는 경우보다 재범률이 유의미하게 낮았다. 마지막으로 이상의 연구 결과를 토대로 본 연구는 전자발찌 부착 성폭력범죄자의 재범 예방 정책을 제안하였다.

In this study, growth enhancing effect of hatchery waste egg decomposed liquid fertilizer in pepper plant cultivation through chlorophyll fluorescence (O-J-I-P) analysis. In a whole growth period, egg decomposed fertilizer treated pepper grew well than non treated plant, though it was not statistically significantly different. Amount of chlorophyll fluorescence of non treated plant was higher thant that of fertilizer treated plant. It is determined that eventually lead to increased photosynthesis. In this study, six parameters, Fo, ABS/RC, RC/ABS, TRo/RC, DI0/RC, and DF Total ABS were the important factors represent efficiency of photochemical responses of pepper plant treated with hatchery waste egg decomposed fertilizer.

Quantum dots(QDs) with their tunable luminescence properties are uniquely suited for use as lumophores in light emitting device. We investigate the microstructural effect on the electroluminescence(EL). Here we report the use of inorganic semiconductors as robust charge transport layers, and demonstrate devices with light emission. We chose mechanically smooth and compositionally amorphous films to prevent electrical shorts. We grew semiconducting oxide films with low free-carrier concentrations to minimize quenching of the QD EL. The hole transport layer(HTL) and electron transport layer(ETL) were chosen to have carrier concentrations and energy-band offsets similar to the QDs so that electron and hole injection into the QD layer was balanced. For the ETL and the HTL, we selected a 40-nm-thick ZnSnOx with a resistivity of 10Ω·cm, which show bright and uniform emission at a 10 V applied bias. Light emitting uniformity was improved by reducing the rpm of QD spin coating.At a QD concentration of 15.0 mg/mL, we observed bright and uniform electroluminescence at a 12 V applied bias. The significant decrease in QD luminescence can be attributed to the non-uniform QD layers. This suggests that we should control the interface between QD layers and charge transport layers to improve the electroluminescence.

The power capacitors used as vehicle inverters must have a small size, high capacitance, high voltage, fast response and wide operating temperature. Our thin film capacitor was fabricated by alumina layers as a dielectric material and a metal electrode instead of a liquid electrolyte in an aluminum electrolytic capacitor. We analyzed the micro structures and the electrical properties of the thin film capacitors fabricated by nano-channel alumina and metal electrodes. The metal electrode was filled into the alumina nano-channel by electroless nickel plating with polyethylene glycol and a palladium catalyst. The spherical metals were formed inside the alumina nano pores. The breakdown voltage and leakage current increased by the chemical reaction of the alumina layer and PdCl2 solution. The thickness of the electroless plated nickel layer was 300 nm. We observed the nano pores in the interface between the alumina layer and the metal electrode. The alumina capacitors with nickel electrodes had a capacitance density of 100 nF/cm2, dielectric loss of 0.01, breakdown voltage of 0.7MV/cm and leakage current of 104μA.

A non-volatile resistive random access memory (RRAM) device with a Cr-doped SrZrO3/SrRuO3 bottom electrode heterostructure was fabricated on SrTiO3 substrates using pulsed laser deposition. During the deposition process, the substrate temperature was 650˚C and the variable ambient oxygen pressure had a range of 50-250 mTorr. The sensitive dependences of the film structure on the processing oxygen pressure are important in controlling the bistable resistive switching of the Cr-doped SrZrO3 film. Therefore, oxygen pressure plays a crucial role in determining electrical properties and film growth characteristics such as various microstructural defects and crystallization. Inside, the microstructure and crystallinity of the Cr-doped SrZrO3 film by oxygen pressure were strong effects on the set, reset switching voltage of the Cr-doped SrZrO3. The bistable switching is related to the defects and controls their number and structure. Therefore, the relation of defects generated and resistive switching behavior by oxygen pressure change will be discussed. We found that deposition conditions and ambient oxygen pressure highly affect the switching behavior. It is suggested that the interface between the top electrode and Cr-doped SrZrO3 perovskite plays an important role in the resistive switching behavior. From I-V characteristics, a typical ON state resistance of 100-200 Ω and a typical OFF state resistance of 1-2 kΩ, were observed. These transition metal-doped perovskite thin films can be used for memory device applications due to their high ON/OFF ratio, simple device structure, and non-volatility.

One of the weak points of the Cr-doped SZO is that until now, it has only been fabricated on perovskite substrates, whereas NiO-ReRAM devices have already been deposited on Si substrates. The fabrication of RAM devices on Si substrates is important for commercialization because conventional electronics are based mainly on silicon materials. Cr-doped ReRAM will find a wide range of applications in embedded systems or conventional memory device manufacturing processes if it can be fabricated on Si substrates. For application of the commercial memory device, Cr-doped SrZrO3 perovskite thin films were deposited on a SrRuO3 bottom electrode/Si(100)substrate using pulsed laser deposition. XRD peaks corresponding to the (112), (004) and (132) planes of both the SZO and SRO were observed with the highest intensity along the (112) direction. The positions of the SZO grains matched those of the SRO grains. A well-controlled interface between the SrZrO3:Cr perovskite and the SrRuO3 bottom electrode were fabricated, so that good resistive switching behavior was observed with an on/off ratio higher than 102. A pulse test showed the switching behavior of the Pt/SrZrO3:Cr/SrRuO3 device under a pulse of 10 kHz for 104 cycles. The resistive switching memory devices made of the Cr-doped SrZrO3 thin films deposited on Si substrates are expected to be more compatible with conventional Si-based electronics.

본 연구에서는 Healey 등(2005)의 데이터를 활용하여 스트레스 정도가 단시간에 변하는 운전상황에서 운전자의 심박변이도 분석을 통해 스트레스 정도에 대한 추정이 가능한지를 예비적으로 평가해 보았다. 단시간에 스트레스 정도가 변하는 운전의 경우 심박변이도 변화 양상은 기존 문헌에 나타난 장거리 운전의 양상과 다르며, meanRR, sdRR, HF, LF/HF, LFnorm, HFnorm의 6가지 심박변이도 파라미터가 스트레스 추정에 유의한 변수로 확인되었다. 정상인 운전자 5명에 대해 6가지 파라미터를 입력변수로, 운전 구간에 따라 변하는 스트레스 정도를 출력변수로 하여 개인별 선형회귀 모델(R2=0.8604±0.0959)을 도출하였으며, 이 선형회귀 모델의 적합성을 평가하기 위하여 심박변이도 데이터를 5분 길이의 16개 세그먼트로 나눈 뒤 실제 스트레스 정도와 추정된 스트레스 정도를 비교해 보았다. 그 결과 일부 세그먼트에서 부정확한 추정 결과가 관찰되기도 하였으나, 실제 스트레스 변화 패턴과 예측된 스트레스 변화 패턴 사이에 높은 상관성이 확인되었다(r=0.8560±0.0619). 향후 운전자 구속을 최소화하면서 측정 가능한 심박변이도 분석 시스템을 개발하고, 이를 Healey 등의 연구에서와 유사한 운전 프로토콜을 통해 다수의 피험자에게 적용함으로써 본 연구결과가 유효한지 검증할 계획이다.

Activated carbon (AC) with very large surface area has high capacitance per weight. However, such activation methods tend to suffer from low yields, below 50%, and are low in electrode density and capacitance per volume. Carbon NanoFibers (CNFs) had high surface area polarizability, high electrical conductivity and chemical stability, as well as extremely high mechanical strength and modulus, which make them an important material for electrochemical capacitors. The electrochemical properties of immobilized CNF electrodes were studied for use as in electrical double layer capacitor (EDLC) applications. Immobilized CNFs on Ni foam grown by thermal chemical vapor deposition (CVD) were successfully fabricated. CNFs had a uniform diameter range from 50 to 60 nm. Surface area was 56 m2/g. CNF electrodes were compared with AC and multi wall carbon nanotube (MWNT) electrodes. The electrochemical performance of the various electrodes was examined with aqueous electrolyte of 2M KOH. Equivalent series resistance (ESR) of the CNF electrodes was lower than that of AC and MWNT electrodes. The specific capacitance of 47.5 F/g of the CNF electrodes was achieved with discharge current density of 1 mA/cm2.

Titanium oxide films and powders are attached onto carbon cloths via RF reactive sputtering and an epoxy resin mixture, respectively. TiO2/carbon composite materials were used to investigate the photoelectrochemical degradation of perchlorate ions in water. The energy band gaps of the RF-sputtered TiO2 thin films ranged from 3.35-3.44 eV. A photocurrent of the powdered TiO2 as illuminated by ultra-violet light for 30 min. was 2.79 mA/cm2. Perchlorate ions in water were shown to be degradable by a UV-illuminated TiO2 powder/carbon/Nafion/carbon composite.

본 연구는 컴퓨터 작업시 머리자세가 상부 승모근의 근전도 활성도에 미치는 영향에 대해 알아보기 위해 실시하였다. 대상자는 상지에 근골계질환이 없는 대학생 5명을 대상으로 하였으며, 표면근전도(MP100WS)를 이용하여 근 활성도를 측정하였다. 실험은 10분 동안 머리를 중립자세로 모니터를 보고 컴퓨터 작업을 수행하는 것과 문서걸이(copy holder)를 보기 위해 머리를 회전하고 컴퓨터 작업을 하는 두 가지 조건을 를 이용하여 비교 분석하였다. 머리를

An experimental study of the fire protection performance of water mist spray subjected to thermal radiation was presented. Downward-directed water mist sprays to interact with an under. gasoline pool fire were experimentally investigated in underground environment. The mass mean diameters of water mist droplet were measured by PMAS under various flow conditions. The developed water mist spray nozzle was satisfied to the criteria of NFPA 750. The mechanism of the fire extinguishment by water mist spray was concluded to be cooling of the fire surface which lead to suppressed of' file1 evaporation. It was proved that the water mist spray system under. lower pressures could be applied to underground fire protection system.

본 연구는 사회경제적 취약계층 학생의 진로결정의 질에 영향을 미치는 요인을 탐색하기 위해 수행되었다. 구체적으로, 자신의 적성이나 흥미, 희망 진학계열 및 진학전공에 대한 정보, 직업세계에 대한 이해 등을 가지고 잠정적으로 미래 진로에 대한 의사결정을 내린 청소년이 획득한 진로정보의 양을 ‘진로결정 시 진로정보 획득수준’이라고 정의하고, 사회 경제적 취약계층 청소년이 진로결정 시 충분한 진로정보에 근거한 진로결정을 하는 것과 관련이 있는 요인을 탐색하였다. 이를 위하여 한국직업능력개발원에서 수집한 한국교육고 용패널조사(KEEP)의 일반계 고등학교 3학년 코호트 1차년도 자료(2004년)와 중학교 3학년 코호트 4차년도 자료(2007년) 가운데 일반계 고등학교 3학년 시점 자료를 활용하였다. 분석 결과 가정의 사회경제적 지위가 낮음에도 , 불구하고 진로결정 시 진로정보 획득수준이 높 은 학생들은 자기탐색 수준이 높고, 자녀에 대한 관심이 높은 가정에서 생활하고 있으며, 학교 내 진로지도 활동에도 다수 참여하고 있는 것으로 나타났다. 이러한 연구결과는 가정 의 사회경제적 배경에 따른 청소년들 간 진로결정 시 진로정보 획득수준 격차를 줄이기 위 한 정책 마련에 시사점을 줄 수 있을 것이다.